Видео

👍

hi what insert was you using for the rub over settings?

🌷

What laser would you recommend for cutting charm connectors for permanent jewelry? Like the “mama” /“bestie” charms

I have a bezel pusher tool for prongs and I use the same pressure u seem to, but sometimes the prongs just don’t bend…not sure if I’m weak or the tool stinks and I need a heavier metal

It would be nice if you would stay within camera range.

Lovely earrings, and well explained video, thank you 🙏!

Hi 👋 please tell me can i grave argent and gold ? Thank

Hey Melissa, thanks for this great video! ❤️ How does it work when I want to solder the ring? Does the inside band also has to be larger? And which book of Alan are you working with? Cause I am considering to buy it myself. Thanks a lot :)

Thank you for this video and sharing your knowledge 😊

Is this able to “engrave” inside rings? You have an attachment for the x-tool as I recall that enables that machine to do that.

Hi Melissa, does this have a hammer action and rpm in one piece or do you need to pieces?

Thank you Melissa for all your knowledge and product reviews. One question: are there any lasers out there that can engrave shiny deep lines like impact pneumatic lasers. All the lasers I ve seen engrave more like etching.

I have wanted a fiber laser so badly.

I'm thinking to buy sandpaper and roll them then sell them pre rolled. Do you think it would work?

Thanks what is the tool that you use on the end after stones are set , that goes over the top of the setting

Can collets for the Foredoom 1070 work with the Marathon III Micromotor SDE-H37L1 handpiece? The collet size is 2.30 mm and only fits my smaller mandrels. I am wanting to get 3.175 mm collet so that I can use smaller adapters for my smaller mandrels without having to constantly change the collets, risking damage each time I have to change it.

Love This!!

Beautiful work ❤😊

What is the name of the book? 😊

Melissa for a beginner what hydraulic press did you suggest that is not so expensive? Thanks 😊❤

Great video! Thank you. I was looking for my dremel flex shaft, but now I just saw how quiet your motor is! Omg I am so jealous hahaha, I think I will buy one 😅

Hello,molim gdje mogu kupiti srebreni lanac za permanent nakit?

It looks like a Cuban chain of the puffy kind that makes a statement wich I like all the links real close Versus a Cuban curb flat has a little spacing in between Great work what I wanted to know is how do flat curbs get made real flat because I love how it shines and has sort of a edge look to it

Great, thank you! Helps me a lot!😍

So you engrave there plates at the same time where you engrave a bat, how you did that like multiple pieces at the same time

I always heard this called Viking knit. Thank you for showing us and clearing up some things.

I know it is a laser but will it wear down smooth a face ring for example? I know nothing about this but I am very interested in it. I love jewelry especially sterling silver. I would like to learn to fix jewelry also.

What hammers did you use? Thanks for posting the sheet gauge in a reply i was going to ask as well. Hi from Sydney Australia. Really like your style of videos. It is so easy to listen to and watch. The books here in Australia are over $120 each. Kindles are about $22 each but I like books so much better than electronic, I'm 70 so very old school.

great video, thanks! super thorough.

Magnifique! Merci...

Perfect, valuable information on softening and hardening wire. I probably canceled 100 peices of jewelry over the past 5 years not knowing this.

I’d love to see them on you! They are gorgeous.

Very nice! The studio looks great, BTW.

The best teacher I've seen so far. Great stuff!

❤️

Hi, with this Device can weld aluminium?

Hello when making wire do you stick to one track at a time tighten all the way down then start back again moving over to the next track size down and repeat? That’s the confusion for me Because it looks like you do a few runs on each track working your way down Reason I ask I’m struggling to make 1.5mm wire I only can get to 2mm then the flange starts you mentioned But I am working my way down like I mentioned Thanks

Comfort fit?

how to indian rs

super

Question: wouldn't hammering it to shape it after texturing flatten it and make the texture disappear? Thanks

Hi. I would like to engrave on stainless steel watch back covers and some jewellery. I have the tts 10watts. It simply isn't etching anything on the metal. 100 power. 100mm/m speed. 10.000 lines/mm. Any suggestions.

Thank you so much for this video! The store I'm purchasing my block from said to anneal it before use, but I was having a hard time finding a video that demonstrates how this is done. Thanks for covering the topic so well! They also recommend that if you live in a humid area and haven't used your block for a while you should place your block in a cast iron pan, place the pan on a burner of your kitchen stove, and gently heat the pan and charcoal block. This will allow any moisture your block has absorbed to gently escape as steam, rather than possibly causing cracks if the steam tries to escape while you're working on your block.

Thank you so much for this review! I am a silversmith and just now researching starting up a PJ business. I really would like at least an 100c, however, I understand that may not be as portable. So I'm leaning towards this model. I do have a few questions though, does this have any way to program settings? If I want to upgrade at some point, do they have a trade in program? Sunstone seems to be the way to go regardless!

Thank you for breaking it down so well. You mentioned they are doing away with the older welders.. i have the PJ welder and was looking to purchase extension but have been debating on just ordering one of the colorful styluses since they are longer.. do you know if new stylus is compatible with the PJ welders as far as the plugin ports?

Excellent video! There are a lot of mostly young ladies looking at this Permanent Jewelry business as I'll make a ton of money. My daughter is one of them. It's going to be a 2-3 year gig. When people realize they must remove their jewelry for X-rays, MRIs, etc.

Could you make these to fit the A4 big shot plus?

Boa tarde Melissa

Thanks Melissa. 😊